Fixation and embedding ;for microscopy;:
Dissect the head away from the body. With a number 11 scalpel blade, gently cut
away one of the eyes to expose the inside of the head. Avoid putting pressure on the
head when cutting (making the other eye 'bulge'). Place the dissected head into 2%
glutaraldehyde in phosphate buffer. This solution should be on ice. Often it is
necessary to tap the head down into the solution as it has a tendency to float.
Alternatively, you can give them a 5 second spin in a microfuge to submerge it.
Add an equal volume of 2% OsO4 in phosphate buffer. Only handle OsO4 in the
hood and wear gloves; it is volatile and extremely toxic. Incubate the mixture for 30 min
on ice. Remove the glutaraldehyde/OsO4 mixture and wash the tissue with cold
phosphate buffer by filling the tube completely. Dispose of waste glutaraldehyde and
OsO4 by adding an excess of dry milk powder to the waste solutions in a bottle. The
deactivated solution can then be safely removed. Add fresh OsO4 to the tissue and
incubate on ice for 1-2 hours. Discard the OsO4 and dehydrate the tissue by successive
10 min incubations on ice in the following ethanol solutions: 30%, 50%, 70%, 90%,
100%. For preparing tissue for electron microscopic analysis, also include an 80% EtOH
wash. Repeat the final 100% EtOH incubation.
Replace the final alcohol treatment with propylene oxide and incubate for 10 min
at room temperature. Handle propylene oxide with gloves and only use it in the hood.
Repeat the propylene oxide wash twice. Add an equal volume of durcapan resin to the
last propylene oxide wash and thoroughly mix. Handle resin with non-latex gloves as it
is carcinogenic when unpolymerized. Incubate overnight at room temperature. Use soft
resin for semi-thin and thick sectioning and use hard resin for thin sectioning.
Replace the resin/propylene oxide mixture with pure resin and incubate at least
4 hours. Place tissue in a drop of resin on a slide. Examine the head under a dissecting
microscope and discard any poorly fixed heads. Dissect away unwanted tissue from the
head. Using a needle, transfer a fixed head to a mold which has been filled with resin.
Useful molds are BEEM or silicone rubber flat embedding molds (Ted Pella Co.). Place
the head very close to the edge of the mold (Figure 1). Orient the head so that the head is
anterior up and the eye to be sectioned is closest to the edge. Make sure that the head is
flat and resting on the bottom of the mold. Bake the resin at 70°C overnight. Bake any
waste resin before discarding.
Figure 1
Sectioning and Staining ;Specimens.
Examine the embedded heads to ensure that they did not shift position while the
resin hardened. Only section those which maintained their correct orientation. Trim the
resin block with a razor blade, preferably the kind which are Teflon coated. Trim away
excess resin which covers the eye. This is diagrammed in Figure 2. Start by trimming
resin to form the face of the block which will be cut. Then cut away resin to form a
trapezoid shape, so that the final form resembles a pyramid with its top lopped off.
Figure 2
Cut sections with your favorite microtome. Section thickness can range from 0.5
to 5 microns for tissue embedded in soft resin, and from 50 to 300 nm for tissue
embedded in hard resin. Sections can be collected either with a wire loop or a shaved
wooden stick. The stick is best for collecting serial sections when section order must be
preserved.
Transfer the sections to a puddle of water on a subbed slide. Place the slide on a
heating block (about 80°C) and allow the water to evaporate. If you wish to examine
unstained sections, add a drop of DPX (Fluka) and a cover slip. If you want to stain
the eye sections, use toluidine blue. Place slides with sections on them onto a heating
block which is at a temperature of 70-80°C. Allow the slides to warm up. Add several
drops of toluidine blue solution (enough to only cover the sections) to the slide, and
incubate. The incubation time is variable: it depends on the temperature of the block,
how much toluidine solution is added, etc. Therefore, make an empirical test by staining
for several different amounts of time. Around 30 seconds is usually optimal. After
incubation, remove the slide and rinse thoroughly with water Examine under the
microscope for how well the staining worked. If necessary, you can repeat the procedure
until staining is optimal. Take care; it is possible to overstain tissue with this procedure.
Allow the slides to completely dry before mounting in DPX.
Solutions:
1) Phosphate buffer. This is 0.1 M Sodium Phosphate pH 7.2. It can be made by mixing
0.2M Na2HPO4 and 0.2M NaH2PO4 in a 72:28 ratio, respectively, and then adding an
equal volume of water.
2) Durcapan Resin. This can be ordered as Durcapan ACM from Fluka. It is based on
the formula for Araldite resin, and is stored for long periods of time at room
temperature as four separate components: epoxy resin (A), hardener (B), accelerator
(C), and plasticiser (D). These components can be mixed together and either used
immediately or stored in aliquots at -20°C. If stored at -20°C, you can freeze-thaw an
aliquot for up to three times without affecting the resin. The resin is quite toxic, so
bake any waste at 70°C overnight before discarding. The recipes for soft and hard
resin are:
SOFT HARD
(grams) (grams)
Resin A 54 50
Hardener B 44.5 50
Accelerator C 2.5 1.75
Plasticiser D 10 0.75
3) Glutaraldehyde and Osmium Tetroxide can be purchased as concentrated solutions from Ted Pella Co. and diluted into phosphate buffer. Store both solutions at 4°C in a sealed container. 2% glutaraldehyde solutions are good for one month, and 2% OsO4 solutions are good for several months. See page 73 for instructions on disposal of waste glutaraldehyde and OsO4.
4) Toluidine Blue Solution. Dissolve toluidine blue and borax to 1% final concentration for each in water. Store it in a wide barrel syringe with a filter attached so that the solution will be filtered immediately before use.
5) Preparing Subbed Slides. Heat 500 ml water to 80°C. Add 5g gelatin (Sigma) and
0.5g chromium potassium sulfate. Stir on a hot plate until dissolved (about two
hours). Place new slides in racks, wash briefly in a warm hemosol solution, rinse with
water. Dip slides in gelatin solution, and dry covered overnight.